收藏本站

AJ8 (J8)
NOTES
1. Switch mounting
Mount the switch with the hole cutting
dimensions shown in the dimensions.
Contact us if you are considering using a
panel of other than the recommended
size and shape.
2. Regarding fastening lead wires to
terminals
1) When connecting the tab terminals,
use a .250 Quick-connect and insert the
terminals straight in.
If they are skewed, the terminals will
require excessive insertion force.
In addition, there is some variation in the
insertion force required for different
receptacles from different manufacturers,
so con?rm how much force is needed
under actual conditions.
Do not solder wires onto tab terminals.
2) With manual soldering: Complete the
soldering connection work within 3
seconds with the tip of the soldering iron
(60W soldering iron) at a temperature of
420 ° C or lower, and take care not to
apply any force to the terminal area.
REFERENCE
1. Outline of UL1054 test
Overload test AJ8: 20A 250V AC
(Power factor 0.75 to 0.8)
50 operation
Endurance test AJ8: 16A 250V AC
(Power factor 0.75 to 0.8)
6 × 10 3 operation
After testing, temperature rise of
terminals should be less than 30 ° C and
Avoid touching the switch with soldering
iron.
Soldering position
When wrapping or soldering a wire
around a terminal, do so in the shaded
area indicated in the diagram at left.
Contact terminal and ground terminal
Refer to the diagram above, “soldering
position,” for details on the position where
a wire should be soldered to a terminal.
When soldering PC board terminals,
keep soldering time to within 5 s at 270 ° C
soldering bath or within 3 s at 350 ° C
soldering bath.
3) The terminals should be connected in
such a way that they are not under
constant stress from the connecting
wires.
4) Terminal material is copper alloy which
may discolor due to ?nger’s oil or after a
long time. But that discoloration does not
effect actual performance.
2. Outline of EN61058-1 test
After switching 5 × 10 3 times on the
above load condition at both 85 + 50 ° C and
25 ± 10 ° C, temperature rise of terminals
should be less than 55 ° C and no
abnormality should be observed in
characteristics.
50 to 100ms
3. Resistance to chemicals
To clean the switch unit, use a neutral
detergent diluted with water.
Do not use acidic or alkaline solvents as
they may damage the switch.
Furthermore, be careful not to get any of
the detergent solution inside of the switch
while cleaning it.
4. Environment
Avoid using and storing these switches in
a location where they will be exposed to
corrosive gases, silicon, or high dust
levels, all of which can have an adverse
effect on the contacts.
5. Take care not to drop the product as
it may impair perfomance.
no abnormality should be observed in
characteristics.
24A
J8: 16A
AC: 250V
(Power factor 0.6)
2 sec.
4 sec.
INTRODUCTION TO 4P CONNECTORS FOR THE AJ8 SWITCH
(produced by Nippon Tanshi co.,Ltd)
Suitable switches: AJ8 switch, .250 Quick-connect terminal
(Note: Terminal guard long type switches are not suitable for this connector.)
Housing
Product number: N1620-4204
Connectors for
AJ8 switch
Receptacle
Product number: 17168-2 (post-plated product for ?ne wires)
17168-M2 (material plated product for ?ne wires)
172131-M2 (for thick wires)
Notes) This AJ8 switch connector is not
available from Panasonic Corporation .
Contact us for further details on this connector.
A E CTB4E 201201-T
Panasonic Corporation
Automation Controls Business Unit
industrial.panasonic.com/ac/e
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
ALS50-12 PWR SUPPLY 12VDC OUT 4.2A
ALS50-24 PWR SUPPLY 24VDC OUT 2.1A
ALS50-3.3 PWR SUPPLY 3.3VDC OUT 9.1A
ALS50-5 POWER SUPPLY 5VDC OUT 9.0A
ALS75-12 POWER SUPPLY 12VDC OUT 6.2A
ALS75-24 POWER SUPPLY 24VDC OUT 3.1A
ALS75-3.3 POWER SUPPLY 3.3VDC OUT 12A
ALS75-5 POWER SUPPLY 5VDC OUT 12A
相关代理商/技术参数
AJ8232BF 功能描述:摇臂开关与扳钮开关 Rocker Switch RoHS:否 制造商:C&K Components 触点形式: 开关功能: 电流额定值:50 mA 电压额定值 AC: 电压额定值 DC:30 V 功率额定值: 端接类型: 执行器:Paddle 颜色: 安装风格:Panel 端子密封: 触点电镀: 照明:Not Illuminated 照明颜色:
AJ8241BF 功能描述:摇臂开关与扳钮开关 SPDT ON-OFF 16A, PCB RoHS:否 制造商:C&K Components 触点形式: 开关功能: 电流额定值:50 mA 电压额定值 AC: 电压额定值 DC:30 V 功率额定值: 端接类型: 执行器:Paddle 颜色: 安装风格:Panel 端子密封: 触点电镀: 照明:Not Illuminated 照明颜色:
AJ87C196JV 制造商:Intel 功能描述:
AJ87C196LB20 制造商:Intel 功能描述:
AJ8R5004ZCF 功能描述:摇臂开关与扳钮开关 SPDT ON-OFF 16A, QC RoHS:否 制造商:C&K Components 触点形式: 开关功能: 电流额定值:50 mA 电压额定值 AC: 电压额定值 DC:30 V 功率额定值: 端接类型: 执行器:Paddle 颜色: 安装风格:Panel 端子密封: 触点电镀: 照明:Not Illuminated 照明颜色:
AJ8W202B 功能描述:摇臂开关与扳钮开关 SPDT ON-OFF 16A, QC RoHS:否 制造商:C&K Components 触点形式: 开关功能: 电流额定值:50 mA 电压额定值 AC: 电压额定值 DC:30 V 功率额定值: 端接类型: 执行器:Paddle 颜色: 安装风格:Panel 端子密封: 触点电镀: 照明:Not Illuminated 照明颜色:
AJ911012B3F 功能描述:摇臂开关与扳钮开关 SPST, ON - OFF 16A, QC RoHS:否 制造商:C&K Components 触点形式: 开关功能: 电流额定值:50 mA 电压额定值 AC: 电压额定值 DC:30 V 功率额定值: 端接类型: 执行器:Paddle 颜色: 安装风格:Panel 端子密封: 触点电镀: 照明:Not Illuminated 照明颜色:
AJ911102B3F 功能描述:摇臂开关与扳钮开关 SPST, ON - ON 16A, QC RoHS:否 制造商:C&K Components 触点形式: 开关功能: 电流额定值:50 mA 电压额定值 AC: 电压额定值 DC:30 V 功率额定值: 端接类型: 执行器:Paddle 颜色: 安装风格:Panel 端子密封: 触点电镀: 照明:Not Illuminated 照明颜色: